Acumen Seals & Pumps Logo

Grundfos CR Pump Seal Replacement: What HQQE Means

2026-11-17 • By Director, Acumen Seals & Pumps Limited
Share:

Grundfos CR vertical multistage pumps run in boosting, washdown, CIP and clean process duties across the UK, and their seals are one of the most common enquiries we get. We select and supply equivalent mechanical seals to suit the CR range, including our own A139S, a cartridge seal with silicon carbide faces and EPDM elastomers, already supplied to suit Grundfos CRN 15 and CRN 20 pumps.

Reading the seal code on the pump plate

The last letters of a Grundfos CR model code tell you which seal is in the pump. Take CR 20-17 A-F-A-E-HQQE as an example: 20 is the nominal flow size, 17 is the number of stages, and HQQE is the shaft seal code. Each letter of the seal code means something:

  • H - the seal type: a balanced cartridge seal
  • Q - the rotating face material: silicon carbide
  • Q - the stationary seat material: silicon carbide
  • E - the elastomers: EPDM

So a pump marked HQQE runs a cartridge seal with silicon carbide faces and EPDM elastomers. HQQV is the same seal with FKM elastomers. The code on your pump plate is the single most useful thing to send us.

Why silicon carbide faces

Silicon carbide is a hard, wear resistant face material, and a hard face running against a hard face copes better with fine particles in the pumped water than a carbon face does. On CR pumps in boosting and process duties, silicon carbide on both faces is the usual arrangement. Our A139S uses silicon carbide faces with EPDM elastomers and a 25 bar pressure limit, to suit CRN 15 and CRN 20 pumps.

EPDM or FKM elastomers

The last letter matters. EPDM (E) suits water, hot water and many cleaning fluids. FKM (V) suits oils and many chemicals, but for hot water and steam duties EPDM is the better choice. Match the elastomer to what the pump actually handles, not just what was in it before - if the duty has changed, tell us and we will check the materials before quoting.

Identifying a seal without the code

If the plate is worn or the code unreadable, the pump model and serial number narrow it down, and a photo of the old seal settles it. Cartridge seals come out as one unit, so the old cartridge and the pump model are usually enough for us to identify the equivalent. We check every enquiry against the pump model before we quote, so listing the CR range here does not mean every variant is covered.

Common questions

What seal does my Grundfos CR pump need?

The seal code on the pump plate - the last letters of the model code, such as HQQE - tells us directly. Send us the full model code and serial number, plus a photo of the old seal if you have one, and we will quote for the equivalent seal.

What does HQQE stand for?

H is the seal type (a balanced cartridge), the two Qs are silicon carbide rotating and stationary faces, and E is EPDM elastomers. It is the standard seal arrangement on CR pumps in water duty.

Do you supply the seal or a repair kit?

We supply the equivalent cartridge seal itself, selected to suit your pump model and duty. Tell us what the pump handles and we will confirm the materials before quoting.

If this failure mode sounds familiar, these are the products and services that usually fix it.

A

Director, Acumen Seals & Pumps Limited

Published on 2026-11-17

45 years in engineering and 36 years in sealing. Andrew specifies, supplies and troubleshoots mechanical seals, FFKM elastomers and pump sealing systems for UK industry.

More about Andrew
#Grundfos#Grundfos CR#Grundfos CRN#HQQE#cartridge seals#mechanical seal replacement#A139S

Share this article

Share: